Washing Machine Repair in Utah

Top-load, front-load and stacked washers that won't drain, spin, fill or lock, diagnosed first by technicians with 10+ years each.

What does washer repair involve?

Washer repairs run $150 to $1,000, depending on the fault, the part and the model. The diagnostic visit is $99 to $159, and it's credited toward the repair if you go ahead. Christian or Tim diagnoses the machine first, then you decide. Every repair carries a 90-day guarantee on parts and labor.

A washer is a handful of systems working in sequence: water comes in through the inlet valve, a level switch or pressure sensor tells the control when the tub is full, the motor agitates or tumbles, the drain pump empties the tub, and the lid or door lock has to confirm it's shut before the basket spins. When one of those steps fails, the cycle stalls at that point. That's why the most useful thing you can tell us is where in the cycle the machine stops. It narrows the fault before we've taken a single screw out.

We don't guess and swap parts. The technician opens the cabinet, tests the suspect components with a meter, and names the one that failed. You get the fault and the price before any repair starts.

Last updated

What the symptoms usually mean

Won't spin? The control won't spin the basket until the lid lock reports that the lid is shut. A failed or burned lock switch leaves you with a tub of wet clothes and a flashing lid light. If the lock checks out, the next suspects are the drive belt, the motor coupler (a small part designed to break so the motor doesn't) and, on many top-loaders, the clutch.

Banging or rumbling? Banging on spin points to worn suspension rods or springs, which let the tub swing into the cabinet. A rumble that grows louder as spin speed rises points to the tub bearing. That's a different, bigger repair, so it's worth telling the two apart before you book.

Stacked units: a stacked washer uses the same washer parts as a standalone machine, but the cabinet comes apart differently and the space is tighter. Tell Samuel it's stacked when you book so the visit is planned for it. For the dryer half, see Dryer Repair.

Front-loaders have their own page. Door boot seals, door locks and drum bearings fail in their own ways. See Front-Load Washer Repair.

Common washer problems

Drains but won't spin
Lid lock switch, drive belt, motor coupler or clutch. The lid lock is the first check because the control simply won't allow a spin without its signal.
Won't drain
Usually the drain pump, often jammed by a sock, coin or bra wire, or a kinked or clogged drain hose. A pump that hums but doesn't move water is typically blocked. A pump that's silent may have failed electrically.
Won't fill or fills slowly
Clogged inlet screens, a failed inlet valve, or a faulty water level switch. Utah's hard water can leave mineral scale on the inlet screens over time, which slows filling.
Bangs or walks on spin
Worn suspension rods, an unbalanced load or unlevel feet. Try a smaller, evenly spread load first. If it still walks, the suspension is the likely cause.
Leaking
Fill hoses, drain hose, pump or tub seal. Where the water shows up helps: at the back usually means hoses, underneath usually means the pump or tub seal.
Samsung front-load washer with the door open after a water leak call, VineyardSub-Zero Model 550 refrigerator grille and badge with dust on the condenser, SpringvilleFrigidaire stacked washer-dryer serviced in Provo

How it works

  1. Call or book online

    Give us the brand, the model number (under the lid or behind the control panel), the washer type, and where in the cycle it stops.

  2. Quick checks while you wait

    If the floor is wet, shut off the taps. Check the drain hose isn't kinked, check the breaker, and note any error code. If the washer stopped full of water, leave it as-is. That standing water tells us where the cycle failed.

  3. Diagnosis

    Christian or Tim opens the cabinet and tests the lid lock, inlet valve, level switch, drain pump and motor, and inspects the belt, coupler and suspension.

  4. You decide

    We name the fault and quote the fix. Say no and you've only paid for the diagnosis.

  5. Repair

    The failed part comes out, the new part goes in, and the machine is run through a cycle. The repair is backed by our 90-day guarantee.

Recent washer jobs

  • Samsung WA45T3200AW top-load, Spanish Fork: lid lock switch assembly replaced. The old switch showed signs of burning.
  • Samsung WF328AAW front-load, Orem: top panel off to diagnose the control board, wiring harness, inlet valves and drum.
  • Frigidaire PFLE3900UW0 stacked washer-dryer, Provo: service call on a compact laundry-area unit.
  • Samsung VRT front-load, Vineyard: water pooling at the base, narrowed to the door boot seal or drum.

Brands we repair

Whirlpool, Samsung, LG, Maytag, GE, Bosch, Speed Queen, Asko, Frigidaire, Electrolux, Amana, Kenmore, Fisher & Paykel, Blomberg, Crosley, Roper, Hotpoint and Haier. If yours isn't listed, call and ask. Washers share the same core parts across brands.

Which washer repair problems do we fix?

FAQ

How much does washer repair cost in Utah?

Repairs run $150 to $1,000, depending on the fault, the part and the model. A lid lock or drain pump sits toward the lower end. A tub bearing or control board sits toward the higher end. The $99 to $159 diagnostic is credited toward the repair if you go ahead.

Why won't my washer drain or spin?

If it won't drain, it's usually the drain pump or a blocked or kinked hose. If it drains but won't spin, start with the lid lock, then the belt, motor coupler or clutch. A machine that won't drain also won't spin, because the control waits for the tub to empty first, so the drain is always checked first.

Do you repair LG, Samsung, Whirlpool and Maytag washers?

Yes, plus every brand listed above. If your brand isn't on the list, call and ask.

Do you repair top-load and front-load washers?

Both, plus stacked units. Front-loaders have some faults of their own, like door boot seals and drum bearings, which are covered on our Front-Load Washer Repair page.

Do you fix stackable washer-dryers?

Yes. Stacked units use the same washer and dryer parts as standalone machines, but the cabinet comes apart differently and there's less room to work. Tell Samuel it's a stacked unit when you book so the technician plans for it. We recently serviced a Frigidaire PFLE3900UW0 stacked washer-dryer in Provo.

Do you serve my area?

We cover Utah County and Salt Lake County, from Layton in the north to Santaquin in the south, including Orem, Lehi, Provo, Spanish Fork and West Jordan. If your town isn't listed on our service areas page, call and ask.

Is the repair guaranteed? Can you come the same day?

Every repair carries a 90-day guarantee on the parts we install and on our labor. For a same-day visit, call before 2pm. That gives you the best chance of getting a technician out the same day.

Should I keep using a washer that's leaking or making noise?

No. A leak can damage the floor and cabinets underneath, and a banging tub can damage the suspension, cabinet or bearing further. Shut off the taps, unplug it, and book a diagnosis.

Tell us what is going on. We'll get back to you.

Every repair carries a 90-day guarantee on the parts we install and on our labor.

  • Rated 4.8 on Google from 290 reviews
  • Monday to Friday, 8am to 5pm
  • Diagnosed first by technicians with more than 10 years each
Prefer to talk? Call(385) 238-1594

Book washer repair

Your details, step 1 of 3

* Required

Format: (XXX) XXX-XXXX

What needs fixing?
When suits you?

Request received.

We've got your details and we'll get back to you. Need us sooner? Call (385) 238-1594.

Rather talk now? (385) 238-1594