Dryer Repair in Utah

No heat, won't turn, noisy, or taking two cycles? We find the fault first, then fix it.

What does dryer repair involve?

Dryer repairs run $150 to $1,000, depending on the fault, the part and the model. The diagnostic visit is $99 to $159, and it's credited toward the repair if you go ahead. Christian or Tim diagnoses first, then you decide. Every repair carries a 90-day guarantee on parts and labor.

A dryer does three jobs at once: it turns the drum, heats the air, and pushes that air out through the vent. The motor turns the drum with a belt and an idler pulley, the drum rides on rollers or glides, a heating element warms the air, and a set of thermostats and a thermal fuse keep the temperature safe. Most dryer faults fall cleanly into one of those three jobs, and the symptom points to which one.

The technician meters the electrical parts, inspects the mechanical ones, checks the airflow, and tells you what failed before anything is replaced.

Last updated

Why the details matter

Why can it spin but stay cold? On an electric dryer, the motor runs on one leg of the 240V supply. The heating element needs both. Lose one leg at the breaker, or lose the element, and the drum turns with no heat. That's why checking the double breaker is the first thing to do.

Why the vent matters. Lint in the vent duct cuts airflow, overheats the dryer and blows the thermal fuse. It's also a fire risk. So we check airflow before replacing a fuse. Replacing a fuse without clearing the vent just means it blows again.

Stacked units. A stacked dryer gets the same diagnosis as a standalone one, just in a tighter space. We recently serviced a Frigidaire PFLE3900UW0 stacked washer-dryer in Provo. For the washer half, see Washer Repair.

Common dryer problems

Tumbles but no heat
Heating element, thermal fuse, thermostats, or one tripped leg of the 240V breaker.
Hums but won't turn
A broken belt, a seized idler pulley or a stuck motor. Don't keep pressing start, because a motor that hums without turning can overheat.
Thump every rotation
A flat spot on a drum roller.
Squeal that rises with speed
The idler pulley or a roller bearing.
Scraping or grinding
A worn drum glide, a loose drum seal, or a coin or bra wire caught between the drum and the cabinet.
Won't start at all
The door switch, start switch, thermal fuse or breaker. On many dryers, a blown thermal fuse stops the whole machine, not just the heat.
Takes two cycles to dry
A blocked vent duct. Clean the lint filter, then go outside and feel for strong airflow at the vent hood while the dryer runs. Weak airflow means a clogged or crushed duct.
Samsung front-load washer with the door open after a water leak call, VineyardSub-Zero Model 550 refrigerator grille and badge with dust on the condenser, SpringvilleSamsung top-load washer repaired in Spanish Fork

How it works

  1. Call or book online

    Give us the brand, the model number (inside the door opening), the symptom, and whether it's stacked.

  2. Quick checks

    Check the double breaker, clean the lint filter, turn the drum by hand, and feel for airflow at the outside vent.

  3. Diagnosis

    Christian or Tim meters the element, fuse, thermostats, door switch and motor, and inspects the belt, pulley, rollers, blower and exhaust.

  4. You decide

    Repair or not, your call.

  5. Repair

    The failed part is replaced, the dryer is run to confirm heat and airflow, and the repair carries a 90-day guarantee.

Brands we repair

Whirlpool, Samsung, LG, Maytag, GE, Speed Queen, Frigidaire, Electrolux, Kenmore, Amana, Bosch, Fisher & Paykel, Roper, Hotpoint and Crosley.

FAQ

How much does dryer repair cost in Utah?

Repairs run $150 to $1,000, depending on the fault, the part and the model. A thermal fuse, belt or roller is at the lower end. A motor or control board is at the higher end. The $99 to $159 diagnostic is credited toward the repair if you go ahead.

Why isn't my dryer getting hot?

The heating element, the thermal fuse, a thermostat, or a tripped leg on the double breaker. Check the breaker first. If both sides are on and it still runs cold, book a diagnosis.

Why does it take two cycles to dry a load?

Usually a lint-clogged vent duct. The dryer is heating, but the moist air can't get out. Clearing the duct often fixes it, and it lowers the fire risk too. If airflow is strong and it's still slow, the thermostats or element may be weak.

Can a dryer belt be replaced?

Yes. If the drum spins freely by hand with no resistance, the belt has likely snapped. It's a common, straightforward repair.

Do you repair Samsung, LG, Maytag and Whirlpool dryers?

Yes, and every brand listed above.

Do you repair stacked washer-dryers?

Yes. Tell Samuel it's stacked when you book.

Is it guaranteed? Where do you work?

Every repair carries a 90-day guarantee on parts and labor. We work across Utah County and Salt Lake County, including Orem, Lehi, Provo, Spanish Fork and West Jordan.

Is it safe to keep using a dryer that smells hot?

No. A burning smell or a dryer that's hot to the touch on the outside can mean a blocked vent or a failing part. Stop using it, unplug it, and call.

Tell us what is going on. We'll get back to you.

Every repair carries a 90-day guarantee on the parts we install and on our labor.

  • Rated 4.8 on Google from 290 reviews
  • Monday to Friday, 8am to 5pm
  • Diagnosed first by technicians with more than 10 years each
Prefer to talk? Call(385) 238-1594

Book dryer repair

Your details, step 1 of 3

* Required

Format: (XXX) XXX-XXXX

What needs fixing?
When suits you?

Request received.

We've got your details and we'll get back to you. Need us sooner? Call (385) 238-1594.

Rather talk now? (385) 238-1594