Ice Maker Repair in Utah

No ice, no water, small cubes or a jammed dispenser? We test the water inlet valve first, then follow the water.

What does ice maker repair involve?

Ice maker repairs run $150 to $1,000, depending on the fault, the part and the model. The diagnostic visit is $99 to $159, and it's credited toward the repair if you go ahead. Christian or Tim diagnoses first, then you decide. Every repair carries a 90-day guarantee on parts and labor.

A refrigerator ice maker runs a short cycle: the inlet valve opens and sends water up the fill tube into the mold, the freezer freezes it, a thermostat or sensor confirms it's frozen, and an ejector motor pushes the cubes into the bin. A bin arm or sensor stops production when the bin is full. In the door, an auger and a chute flap move the ice out. Every part of that chain can fail, so we follow the water from the valve to the bin.

Last updated

Key point: one inlet valve feeds both the ice maker and the water dispenser, so a single failed valve can take out both. If you've lost ice and water, start there.

Hard water: Utah's hard water leaves scale on the fill tube, inlet valve and mold over time. That can slow the fill, shrink the cubes, or stop production. If scale is the cause, the diagnosis will find it.

Scotsman ice machines

A standalone Scotsman is a different job from a fridge ice maker. It has its own water pump, evaporator plate, harvest cycle and condenser. Common faults are low production, a harvest that won't complete, thin or bridged ice, and shutdown codes. We service Scotsman machines at home and in commercial settings. Give us the model number when you book.

Recent job: Sub-Zero Model 550, Springville. Water inlet valve replaced with OEM Sub-Zero part #4201440.

Common ice maker problems

No ice and no water
The water inlet valve, the supply line or a clogged filter.
No ice, but the dispenser works
A frozen fill tube, the mold thermostat, the ejector motor, the control, or a bin arm stuck in the "full" position.
Small, hollow or cloudy cubes
Low water pressure, a restricted filter or a half-open valve.
Sheet of ice in the bin
A valve that won't close fully, letting water drip in and freeze into a block.
Frost in the door ice compartment
A leaky compartment seal or chute flap letting moist air in.
Ice is made but won't dispense
The auger motor, the chute flap, or cubes fused together in the bin.
Dispenser dead for both ice and water
The control board, a door switch, or the child-lock setting.
Samsung front-load washer with the top panel off for diagnosis, OremFrigidaire stacked washer-dryer serviced in ProvoSamsung front-load washer with the door open after a water leak call, Vineyard

How it works

  1. Call or book online

    Give us the brand, the model number, and exactly what stopped: ice, water or both. Is it a freezer ice maker or a door ice maker?

  2. Quick checks

    Is the freezer at 0°F? Is the supply valve open? Is the ice maker switched on? Is there ice in the fill tube? When was the filter last changed?

  3. Diagnosis

    We check the freezer temperature, the valve's voltage and flow, the fill tube, the ejector cycle, the bin sensor, the auger and the dispenser switches.

  4. You decide

    Repair or not, your call.

  5. Repair

    The part is replaced, and the repair carries a 90-day guarantee.

Brands we repair

Samsung, LG, Whirlpool, GE, Frigidaire, KitchenAid, Maytag, Kenmore, Bosch, Sub-Zero, Viking, Thermador, Fisher & Paykel and Scotsman.

FAQ

Why is my ice maker not working?

If the water dispenser is also dead, it's the inlet valve, the supply line or the filter. If the water still works, the problem is inside the ice maker itself: the fill tube, the thermostat, the ejector motor, the bin arm or the control.

How much does ice maker repair cost?

Repairs run $150 to $1,000, depending on the fault, the part and the model. The $99 to $159 diagnostic is credited toward the repair if you go ahead.

Why is my Samsung ice maker freezing up?

Usually a valve that won't fully close, or moist air leaking into the door ice compartment through a worn seal and freezing on the parts. Clearing the ice fixes it for a while, but the cause has to be repaired or it comes back.

Do you repair Scotsman ice machines in Utah County?

Yes, both home and commercial units.

Can a Sub-Zero inlet valve be replaced?

Yes. We use OEM parts. We recently replaced one on a Sub-Zero Model 550 in Springville with part #4201440.

Why is my ice maker slow?

A freezer warmer than 0°F, low water pressure or a clogged filter. Check the freezer temperature with a thermometer and change the filter if it's overdue.

Should I call about the ice maker or the fridge?

Either. We check both. If the fridge itself is warm or leaking, see Refrigerator Repair.

Tell us what is going on. We'll get back to you.

Every repair carries a 90-day guarantee on the parts we install and on our labor.

  • Rated 4.8 on Google from 290 reviews
  • Monday to Friday, 8am to 5pm
  • Diagnosed first by technicians with more than 10 years each
Prefer to talk? Call(385) 238-1594

Book ice maker repair

Your details, step 1 of 3

* Required

Format: (XXX) XXX-XXXX

What needs fixing?
When suits you?

Request received.

We've got your details and we'll get back to you. Need us sooner? Call (385) 238-1594.

Rather talk now? (385) 238-1594